Amorphous Silicon TFTs in Displays: Passive vs Active Matrix

•

 5 min read

YouTube video ID: 5cwOeOKrA4A

Source: YouTube video — Watch original video

PDF

Amorphous silicon (a-Si) plays a crucial role in microelectronic devices, particularly in displays and, historically, in solar cells. This material is favored for its ability to be deposited on amorphous substrates like glass, where single-crystalline silicon cannot be grown.

Display Technologies: Passive vs. Active Matrix

Displays fundamentally aim to control an array of pixels to create spatial light emission patterns. Early display architectures used a "direct drive" method, where each pixel required a pair of electrodes, leading to a non-scalable system (2n contacts for n pixels). This approach was seen in early LCD calculators.

To address scalability for displays with millions of pixels, two main architectures emerged: passive matrix and active matrix, both utilizing a crossbar structure. In this setup, horizontal "scan lines" and vertical "data lines" intersect, with a pixel at each cross point. Applying bias across a corresponding horizontal and vertical wire lights up a pixel.

Passive Matrix Displays

In a passive matrix display, there is no individual switch co-located with each pixel. This leads to a "crosstalk" problem: attempting to light up a single pixel by biasing its corresponding row and column also inadvertently biases other pixels at the intersection of the selected row and other selected columns, and vice-versa. To mitigate this, passive matrix displays operate by "row-by-row scanning," where one scan line is biased at a time, and data lines are selectively biased to light up pixels in that row.

  • Advantages:
    • Significantly simpler electrical contact structure (m+n contacts for an m x n array) compared to direct drive.
  • Disadvantages:
    • Slow, as patterns are displayed line by line.
    • Prone to crosstalk if not carefully managed.

Active Matrix Displays (AMLCD and AMOLED)

Active matrix displays also use a crossbar structure, but critically, each pixel integrates a thin-film transistor (TFT). This TFT acts as an electrical switch, allowing individual control of each pixel and eliminating crosstalk issues. Since most displays are built on glass, and single-crystalline silicon cannot be grown on amorphous glass, amorphous silicon (or polysilicon) is used for these TFTs.

There are two primary variants of active matrix displays:

  1. Active Matrix Liquid Crystal Display (AMLCD):

    • Structure: Consists of a backlight (constant white light source), a bottom linear polarizer, a TFT backplane, a liquid crystal layer, a color filter, and a top linear polarizer (oriented 90 degrees to the bottom one).
    • Operation: Liquid crystals are optically chiral materials whose polarization plane rotation can be electrically controlled.
      • Off-state (no bias): Light from the bottom polarizer passes through the liquid crystal without polarization rotation and is blocked by the top polarizer.
      • On-state (bias applied): The liquid crystal rotates the light's polarization by 90 degrees, aligning it with the top polarizer, allowing light transmission.
    • Color: Achieved using red, green, and blue color filters, which selectively transmit light.
    • Characteristics:
      • Voltage-driven device.
      • Wastes a lot of light due to polarizers and color filters.
      • Backlight is always on, leading to constant power consumption.
      • Mature, well-established, and relatively low-cost technology, still used in low-end displays.
  2. Active Matrix Organic Light Emitting Diode (AMOLED):

    • Structure: Directly uses organic light-emitting diodes (OLEDs) for each pixel, which can be processed to emit different colors (red, green, blue). Often includes a circular polarizer and a metal mirror behind the TFT backplane.
    • Operation: OLEDs emit light directly when current flows through them.
      • On-state: Current is sent through the OLED, causing it to light up.
      • Off-state: No current is sent, and the OLED remains dark.
    • Polarizer/Mirror Function: The metal mirror reclaims downward-emitted light, increasing efficiency. The circular polarizer prevents ambient light from reflecting off the mirror and reducing display contrast. Ambient light passing through the polarizer, reflecting off the mirror, has its handedness flipped and is then blocked by the polarizer on its way out.
    • Characteristics:
      • Current-driven device.
      • More energy-efficient than AMLCD due to fewer light loss mechanisms and no always-on backlight.
      • More advanced and recent generation of displays, common in high-end devices like smartphones.

Thin-Film Transistors (TFTs)

TFTs are the core switching elements in active matrix displays. A typical cross-sectional structure includes:

  • Substrate: Display glass (e.g., sodium-free glass prepared by downdraw method for flatness and purity).
  • Gate: Metal electrical conductor.
  • Gate Dielectric: Typically silicon nitride, deposited via PECVD.
  • Amorphous Silicon: The semiconductor material.
  • Source and Drain Electrodes: Control current flow.

Operation (Field Effect Transistor): By applying a positive bias to the gate, positive charges accumulate on the gate, and negative charges (electrons) accumulate at the interface between the amorphous silicon and the gate dielectric. This forms an "n-channel" – a thin, conductive layer of electrons. Undoped amorphous silicon has low conductivity, but this electrostatic doping makes the channel conductive, allowing current to flow between the source and drain. Changing the gate bias switches the device on or off.

I-V Curve Characteristics: The current-voltage (I-V) curve for a TFT shows two main regimes:

  • Linear Regime: At low source-drain bias, current scales linearly with bias. A conductive channel is present, and higher bias leads to more current.
  • Saturation Regime: At higher source-drain bias, the curve plateaus. This is due to "pinch-off," where the n-channel becomes disconnected from the negative contact (drain) due to electrostatic repulsion from the large negative bias. Further increasing the bias does not significantly increase current, as the disconnected region restricts flow. In this regime, the gate voltage effectively controls the current, making it a good switch.

Amorphous Silicon vs. Low-Temperature Polysilicon (LTPS)

Two main materials are used for TFTs: amorphous silicon (a-Si) and low-temperature polysilicon (LTPS).

  • LTPS Preparation: LTPS is made by first depositing amorphous silicon and then crystallizing it.

    • Blanket Annealing: Heating in a furnace to 600°C. Less preferred due to high temperature (can deform glass, damage other components) and uncontrolled, random nucleation.
    • Excimer Laser Annealing (ELA): Uses short-wavelength UV lasers (e.g., 305 nm) to induce localized crystallization.
      • Sequential Laser Solidification (SLS): A preferred ELA method where a laser spot induces nucleation in one region, then is translated laterally to grow existing nuclei. This results in directional, almost single-crystalline grains with fewer defects and higher quality.
      • Localized Heating: ELA's localized heating allows processing on temperature-sensitive substrates like polymers for flexible displays, as temperature drops rapidly a few tens of microns away from the laser spot.
  • Material Properties and Applications:

    | Feature | Amorphous Silicon (a-Si) TFTs | Low-Temperature Polysilicon (LTPS) TFTs

  Takeaways

  • Passive matrix displays use row-by-row scanning without per-pixel switches, leading to slower refresh and crosstalk issues that must be managed.
  • Active matrix displays incorporate a thin‑film transistor (TFT) at each pixel, providing individual switching, eliminating crosstalk, and enabling higher resolution and faster response.
  • AMLCDs rely on a constant backlight and polarizers, consuming more power and wasting light, whereas AMOLEDs use self‑emissive OLEDs, are current‑driven, and achieve greater energy efficiency.
  • Amorphous silicon is the common semiconductor for TFTs on glass because crystalline silicon cannot be grown on amorphous substrates, while low‑temperature polysilicon (LTPS) offers higher mobility but requires laser or high‑temperature annealing.
  • The TFT operation creates an n‑channel by electrostatic doping; its I‑V curve shows a linear regime at low drain bias and a saturation regime where pinch‑off limits current, making the device an effective switch.

Frequently Asked Questions

How does the thin‑film transistor (TFT) in an active matrix display form a conductive channel?

The TFT forms a conductive n‑channel by applying a positive gate bias, which attracts electrons to the interface between the amorphous silicon layer and the gate dielectric, electrostatically doping the region. This channel allows current to flow between source and drain, turning the pixel on; removing the bias collapses the channel, turning it off.

What benefit does excimer laser annealing (ELA) provide when creating low‑temperature polysilicon TFTs?

ELA uses short‑wavelength UV pulses to locally melt and crystallize amorphous silicon, producing directional, large‑grain polysilicon without heating the entire substrate. This enables processing on temperature‑sensitive glass or polymer sheets, reduces defects compared with blanket annealing, and yields higher carrier mobility for faster TFTs.

Does this page include the full transcript of the video?

Yes, the full transcript for this video is available on this page. Click 'Show transcript' in the sidebar to read it.

Helpful resources related to this video

If you want to practice or explore the concepts discussed in the video, these commonly used tools may help.

Links may be affiliate links. We only include resources that are genuinely relevant to the topic.

Full transcript is not shown on this page

This page focuses on the summary and original notes. For full verification, refer to the original YouTube video.

PDF