Glass Viscosity Reference Points and Processing Techniques

•

 11 min read

YouTube video ID: MUn9aT8lOXA

Source: YouTube video — Watch original video

PDF

Glass viscosity is a critical parameter in glass processing, with several key reference points defining its behavior. The horizontal axis of a viscosity chart typically represents viscosity on a logarithmic scale.

  • Working Point (10^3 Pa·s): Below this viscosity, glass behaves like a regular fluid, making it difficult to hold any shape. Glass shaping requires viscosity to be higher than the working point.
  • Softening Point (10^6.6 Pa·s): Above this viscosity, the glass melt becomes too stiff to deform easily.
  • Working Range: The region between the working point and the softening point is the "working range" for glass melt. Within this range, glass behaves like chewing gum, allowing for easy shaping and retention of geometry. Many glass shaping techniques operate within this viscosity window.
  • Annealing Point (10^12 Pa·s): This point coincides with the glass transition temperature (Tg). At the annealing point, microscopic changes can still occur, allowing for the relaxation of internal stresses and strains without macroscopic shape distortion. This is crucial for post-shaping annealing to prevent premature cracking. For context, pitch, a very viscous fluid, has a viscosity of about 10^8 Pa·s, highlighting how high 10^12 Pa·s is.
  • Straining Point: Above the straining point, even microstructural relaxation ceases. Annealing processes typically occur between the annealing point and the straining point to facilitate stress relaxation.

Controlling glass viscosity is primarily achieved by adjusting temperature. Viscosity changes by many orders of magnitude with temperature due to its activated nature, as described by the Angell plot.

Viscosity Behavior in Amorphous Polymers

Amorphous polymers, or polymers containing an amorphous phase, exhibit a characteristic temperature-dependent viscosity curve:

  • Low Temperature: Polymers behave like hard, rigid plastics, resisting deformation.
  • Rubbery State: Beyond the glass transition temperature, molecular chains gain enough energy to move, leading to a rubber-like state.
  • Liquid/Glass-Forming Liquid: Further heating transforms the polymer into a liquid.

This viscosity behavior can be engineered by altering the polymer's microstructure:

  • Increasing Tg: Adding stiff chemical groups, like benzene rings, increases the stiffness of polymer chains, raising viscosity and thus Tg.
  • Decreasing Tg: Adding plasticizers (small molecule solvents) acts as molecular lubricants, reducing internal friction between polymer chains and making them easier to move, thereby decreasing Tg. An example is a polymer with a Tg of around 70°C, which softens in hot water for molding and stiffens upon cooling to room temperature (e.g., "Foam Cards").

Viscosity in Inorganic Glasses

For inorganic glasses, viscosity is closely linked to network connectivity. Higher connectivity generally leads to higher viscosity and higher Tg.

  • Silica Glass (SiO2): Exhibits an extremely high working range, often beyond typical processing temperatures. This makes silica glass products rarer and more expensive, as standard glass workshops lack furnaces capable of reaching the necessary temperatures.
  • Borosilicate Glasses: Have higher viscosity and Tg compared to soda-lime glasses due to increased network connectivity from boron. This also makes them more challenging to process.
  • Alkaline Additions: Adding alkaline elements decreases network connectivity, thereby reducing viscosity and glass processing temperatures.

Mixed Alkaline Effect

A significant phenomenon is the "mixed alkaline effect," where adding two or more types of alkaline atoms simultaneously leads to a more substantial decrease in viscosity than adding a single type. This effect is also observed in other transport properties, such as diffusion coefficients, where a minimum diffusion is seen at intermediate compositions.

The most commonly assumed origin of the mixed alkaline effect is the mutual blocking of transport pathways between ions. In a network with only one type of ion (e.g., sodium), ions can hop between similar energy sites. However, with mixed alkaline ions, different sized ions create sites with large energy differences, making it harder for ions (especially larger ones like potassium) to squeeze into smaller sites, thus inhibiting transport and increasing energy barriers.

Historically, this effect was observed in early glass thermometers. Freshly made thermometers would show 0°C in ice water, but after being heated in boiling water and returned to ice water, they would show -5°C. This was due to microscopic deformation and stress relaxation at high temperatures. Storing the glass for several months before making the thermometer eliminated this effect, as relaxation occurred over time. However, reheating and quenching would reintroduce the problem. Crucially, this relaxation effect was diminished tenfold when only one type of alkaline ion was used, providing early evidence of the mixed alkaline effect.

Shear Rate Dependence of Viscosity

Viscosity is not only temperature-dependent but also shear-rate dependent in many fluids, including glass-forming liquids.

  • Newtonian Fluid: Viscosity is constant, independent of shear rate. Shear stress is proportional to shear strain rate.
  • Shear Thinning: As shear rate increases, the liquid becomes thinner (lower viscosity, more flowable).
  • Shear Thickening: As shear rate increases, the liquid becomes thicker (higher viscosity).
  • Bingham Plastic: Behaves like a solid below a certain stress threshold, then flows like a liquid once the threshold is exceeded (e.g., toothpaste).

Microscopically, shear thickening can be attributed to "hydroclustering," where molecules self-assemble into larger clusters at higher shear rates, impeding viscous flow. Oobleck (starch and water) is a common example: it flows like a liquid when stirred slowly but behaves like a solid when subjected to rapid force, allowing people to run on it. Silly Putty also exhibits this behavior.

Shear thinning is desirable for applications like house paint. When brushing, low viscosity allows for uniform application, but once applied, the increased viscosity (due to reduced shear) prevents it from flowing before drying. In 3D printing, shear thinning fluids are advantageous because they have low viscosity at the nozzle (high shear rate) for easy extrusion, but high viscosity once extruded (low shear rate) to hold the printed shape.

Soda-lime glass exhibits shear-thinning behavior. This is important in processes like optical fiber drawing, where the shear rate varies significantly along the fiber. The deformation rate is very small at the thick preform but very large at the thin fiber section. Accounting for this viscosity change is crucial for accurate modeling and preventing defects.

Cats as Non-Newtonian Fluids

An entertaining academic paper has identified cats as non-Newtonian fluids, fitting fluid dynamic equations to describe their behavior. Cats can conform to different shapes, rest on uneven surfaces, exhibit non-wetting behavior on water, glide on smooth surfaces, and cling to vertical walls—behaviors typically associated with liquids.

Measuring Glass Viscosity

Measuring viscosity across its wide range requires different techniques:

  • Low Viscosity (Flowable Liquid): Rotating cylinder viscometers are used. The liquid is placed between a rotating cylinder and a container, and the torque required to spin the cylinder at a given rate is measured to infer viscosity.
  • Intermediate Viscosity (Working Range, Chewing Gum-like): Parallel plate viscometers are employed. Glass material is placed between two parallel plates, and the torque needed to rotate one plate relative to the other is measured. This method is suitable for materials that can hold their shape.
  • High Viscosity (Around Tg, Solid-like): Techniques borrowed from solid mechanics, such as beam bending, are used. Unlike measuring elastic constants (force vs. displacement), viscosity measurement focuses on force as a function of deformation rate. This allows measurement up to about 10^13 Pa·s.
  • Extremely High Viscosity (e.g., Telescope Mirrors): Optical interference is used for very slow deformation over extended periods. By placing a glass sample against a reference plate and shining light, interference fringes reveal the gap width with nanometer precision. Measuring changes in this gap over years (e.g., a 6-year study measured nanometer deformation to capture viscosities of 10^15 to 10^17 Pa·s) allows for the determination of extremely high viscosities.

Is Glass a Solid or a Viscous Fluid at Room Temperature?

Calculations based on experimental viscosity measurements extrapolated to room temperature using the MYEGA equation indicate that soda-lime glass at room temperature has a viscosity of 10^24 to 10^25 Pa·s. This is 12 orders of magnitude higher than Tg and 16 orders of magnitude higher than pitch. The conclusion is that it would take billions of years for a maximum flow of about one nanometer. Therefore, soda-lime glass at room temperature can be treated as an elastic solid, with negligible viscous behavior.

The common misconception that medieval cathedral windows are thicker at the bottom due to glass flow is incorrect. The uneven thickness is a result of manufacturing imperfections at the time, with thicker sections intentionally placed at the bottom for mechanical stability. Instances of thicker sections at the top are simply assembly errors.

Elasticity vs. Viscosity

  • Elasticity: Instantaneous, reversible, and temperature-insensitive. It arises from repulsive/attractive forces between molecules.
  • Viscosity: Rate-dependent, permanent, and highly temperature-sensitive. It involves the relative motion of molecules or atoms, which is an activated process. The temperature dependence can be described by Arrhenius, MYEGA, or VFT equations, depending on whether the fluid is "strong" or "fragile."
  • Non-Newtonian Flow: Glass often exhibits non-Newtonian viscous flow, where viscosity depends on the strain rate.

Glass Shaping Techniques

The continuous viscosity-temperature curve of glass is crucial for its processing versatility. Unlike crystalline materials that undergo abrupt melting, glass gradually transforms from a hot solid to a slowly softening liquid, allowing precise control over viscosity by temperature. This enables glassworkers to manipulate and shape it without it chipping away or collapsing.

Most glass processing occurs within the "working range," where glass has a chewing gum-like consistency.

  • Float Glass Process: Used for large, flat sheets (e.g., window panes). Molten glass floats on a bath of molten tin, spreading due to surface tension and gravity to form a flat surface. This process operates at lower viscosities to facilitate flow. It's a continuous, 24/7 manufacturing process.
    • Ingredients: Sand (SiO2), soda (sodium carbonate), limestone (calcium oxide from dolomite), and cullet (recycled glass). Cullet is vital as it lowers the melting temperature, reducing energy consumption by up to 20% by forming an early liquid phase.
    • Process Steps: Batching (mixing raw materials), melting in a furnace, feeding into a tin float bath, annealing in a "lear" (furnace) to relieve internal stresses, and finally cutting and packaging.
    • Advanced Float Glass: Can produce ultra-thin glass (0.1 mm thick, 4 meters wide) with remarkable surface quality (1.5 nm RMS roughness on top). However, the bottom surface, in contact with tin, can have higher roughness (3-4 nm) and potential contamination.
  • Down-Draw/Fusion Processes (e.g., Schott's Down-Draw, Corning's Fusion Process): Used for high-end applications requiring pristine surface quality (e.g., cover glass for electronics). These processes avoid contact with any substance during glass formation.
    • Schott's Down-Draw: Molten glass flows out of an orifice at the bottom of a furnace and drops by gravity, forming a continuous glass ribbon.
    • Corning's Fusion Process: Molten glass overflows from a crucible, flowing down two sides of a wedge-shaped bottom, where the two streams fuse to form a single sheet of glass. This ensures both surfaces are untouched. These processes were developed in the 1960s but gained renewed interest with the rise of consumer electronics.
  • Glass Blowing (Manual): Involves collecting a "gulp" of molten glass on a hollow blowpipe, blowing air into it, and pushing it against a mold to conform to its shape. The resulting structure with an air bubble is called a "parison." This is a highly skilled craft, often passed down through generations, used for specialized scientific instruments and artistic pieces. The person doing the blowing is called a "gaffer."
  • Industrial Glass Blowing (Containers):
    • Blow-Blow Process (Narrow-neck containers like beverage bottles): A gob of glass is blown into a "parison" in a first mold, then transferred to a second mold and blown again to achieve the final geometry. This two-step process minimizes local shear strain and friction with the mold, ensuring uniform deformation and mold longevity.
    • Press-and-Blow Process (Wide-mouth jars): Similar to blow-blow, but the initial parison is formed by a mechanical press instead of compressed air.
    • Post-Forming Treatments:
      • Hot-End Coating (Tin Oxide): Applied to increase hardness and scratch resistance. It also makes the surface more hydrophobic, improving adhesion for subsequent polymer coatings.
      • Annealing (in a lear): Reheats and gradually cools containers to relieve internal stresses from uneven cooling.
      • Cold-End Coating (Polymer): Applied to provide scratch resistance and reduce friction for smooth travel on filling lines.
      • Delamination (for soda-lime containers): SO2 or SO3 gas (or solid ammonium sulfate) reacts with sodium on the glass surface to form water-soluble sodium sulfate, which is then rinsed off. This prevents sodium leaching into aqueous solutions, which can alter taste and increase pH.

Recycling glass (cullet) is crucial for energy savings and reducing the carbon footprint of the industry. Different types of glass (e.g., soda-lime, borosilicate) must be sorted before recycling to avoid contamination and processing issues.

  Takeaways

  • The working point at 10^3 Pa·s marks the lower limit where glass can hold shape, and the softening point at 10^6.6 Pa·s defines the upper limit of the practical working range for shaping glass.
  • The annealing point (10^12 Pa·s) coincides with Tg, allowing stress relaxation without macroscopic deformation, while the straining point marks the end of micro‑structural relaxation.
  • In inorganic glasses, higher network connectivity raises viscosity and Tg; adding alkaline modifiers reduces connectivity, lowering both, and the mixed alkaline effect can dramatically decrease viscosity when multiple alkali ions are present.
  • Viscosity is also shear‑rate dependent; soda‑lime glass exhibits shear‑thinning, which is exploited in processes like optical fiber drawing and 3D printing to balance flow and shape retention.

Frequently Asked Questions

Why does the mixed alkaline effect cause a larger viscosity reduction than adding a single alkali ion?

The mixed alkaline effect reduces viscosity more than a single alkali because different sized ions create mismatched energy sites that block each other's movement, increasing the activation barrier for ion hopping. This mutual blocking hampers transport pathways, leading to a pronounced drop in viscosity at intermediate compositions.

How is the annealing point related to the glass transition temperature and stress relaxation?

The annealing point occurs at the glass transition temperature (Tg) where the material’s viscosity reaches about 10^12 Pa·s, allowing microscopic rearrangements that relieve internal stresses without changing the macroscopic shape. Operating between the annealing and straining points enables controlled stress relaxation during cooling.

Does this page include the full transcript of the video?

Yes, the full transcript for this video is available on this page. Click 'Show transcript' in the sidebar to read it.

Is Glass a Solid or a Viscous Fluid at Room Temperature?

Calculations based on experimental viscosity measurements extrapolated to room temperature using the MYEGA equation indicate that soda-lime glass at room temperature has a viscosity of 10^24 to 10^25 Pa·s. This is 12 orders of magnitude higher than Tg and 16 orders of magnitude higher than pitch. The conclusion is that it would take billions of years for a maximum flow of about one nanometer. Therefore, soda-lime glass at room temperature can be treated as an elastic solid, with negligible viscous behavior. The common misconception that medieval cathedral windows are thicker at the bottom due to glass flow is incorrect. The uneven thickness is a result of manufacturing imperfections at the time, with thicker sections intentionally placed at the bottom for mechanical stability. Instances of thicker sections at the top are simply assembly errors.

Helpful resources related to this video

If you want to practice or explore the concepts discussed in the video, these commonly used tools may help.

Links may be affiliate links. We only include resources that are genuinely relevant to the topic.

Full transcript is not shown on this page

This page focuses on the summary and original notes. For full verification, refer to the original YouTube video.

PDF