MIT Glass Lab Shows Thermal Expansion, Tempering, and Blowing
Peter Houk, Program Director for the MIT Glass Lab, and Mariel Bass, a senior instructor, demonstrated various properties of glass, focusing on thermal expansion, engineered stress, and glass blowing techniques.
Understanding Glass Properties
Glass is a diverse family of amorphous materials with varied compositions, leading to different coefficients of thermal expansion. This property dictates how glass reacts to temperature changes and how different types of glass interact when combined.
Thermal Expansion and Compatibility
The demonstration began by illustrating the effects of combining two glasses with different compositions and, consequently, different coefficients of thermal expansion. When two such glasses are heated and then cooled together, the differing expansion and contraction rates create stress within the material.
Engineered Stress: Tempering and Hypertempering
The second part of the demonstration focused on engineered stress in glass, specifically tempering and "hypertempering" (Prince Rupert drops).
Tempering involves rapidly cooling the exterior of a heated glass object while the interior remains hot. This process causes the outer layer to compress, while the inner layer attempts to expand, creating a state of tension and compression.
The benefits of tempering glass are twofold: 1. Increased Strength: Tempered glass is significantly stronger than untempered glass. 2. Safety upon Breakage: When tempered glass breaks, it shatters into small, relatively harmless pieces, unlike untempered glass which produces large, sharp shards. This is why tempered glass is used in car windshields (often laminated for additional safety) and skyscraper windows.
In industrial settings, tempering is achieved by heating glass to its transition temperature and then rapidly cooling it with compressed air, ensuring even cooling to prevent uneven stress distribution.
Hypertempering (Prince Rupert Drops) takes this concept to an extreme by using water as a coolant instead of air. Water is a much more radical coolant, generating significantly more stress in the glass. A Prince Rupert drop is formed by allowing molten glass (around 2150°F) to fall into room-temperature water, cooling it in a matter of seconds.
Properties of Prince Rupert Drops: * Extreme Strength: The bulbous head of a Prince Rupert drop is incredibly strong and difficult to break, often requiring significant force. * Catastrophic Failure: Despite its strength, if the tail of a Prince Rupert drop is broken, the entire structure disintegrates almost instantaneously at the speed of sound in glass. This rapid disintegration is due to the immense internal stress. * Fracture Pattern: The resulting fragments are much smaller than those from conventionally tempered glass, indicating a higher degree of internal stress. The fracture pattern often exhibits a cone shape, with the failure propagating from the center at a specific angle, possibly related to shear stress.
Glass Lab Operations and Techniques
The MIT Glass Lab utilizes specific equipment and techniques for glass melting and manipulation.
Furnaces
- Continuous Feed Furnace: This large furnace holds approximately 300-350 pounds of molten glass and operates continuously, often for five to six years without being turned off. It has two chambers separated by a wall with a hole, allowing for continuous migration of glass from the charging side (where raw material is added) to the gathering side (where glass is collected for use). This design ensures a constant supply of good quality glass for daily use.
- Reheating Furnaces (Glory Holes): These furnaces are used to reheat glass during the working process and are turned off at the end of each day. They operate at similar temperatures to the main melting furnace.
Raw Materials
The lab uses pre-made glass "cullet" rather than raw batch materials (sand, soda ash, calcium carbonate) to avoid airborne silica.
Glass Coloring
Colored glass is made by incorporating various metal oxides into the frit (ground glass). * Gold: Often contains silver salts like silver nitrate. * Blues: Typically contain cobalt, sometimes copper. * Reds: Can be made with gold nanoparticles or copper. * Greens: Chromium, copper, or iron can produce green hues.
Glass Blowing Demonstration: Making a Cane Object
The process of creating a blown glass object using pre-made colored cane was demonstrated.
- Making Starter Cane: A small gather of clear glass is coated with fritted colored glass (e.g., gold) and then covered with another layer of clear glass. This is then pulled into a long, thin rod called cane.
- Preparing the Blowpipe: A small, even gather of glass is collected on the end of a hollow blowpipe. A bubble is blown and then popped back into the furnace, creating an open bubble. This open bubble is then shaped into a cylinder of the desired diameter using centrifugal force and gravity.
- Arranging and Fusing Cane: Pre-made colored canes (e.g., MIT's red and gray) are arranged on a preheated ceramic plate. The plate is heated to prevent thermal shock when the canes are picked up.
- Gathering the Cane: The hot glass on the blowpipe is rolled over the arranged canes, picking them up.
- Fusing and Closing: The canes are then rolled and "smashed" on a steel marver table to fuse them together along their length, ensuring a strong joint. The end of the cane assembly is then closed off using a torch, making it inflatable.
- Blowing the Object: Compressed air, introduced via a foot pedal (a system developed during COVID to avoid mouth contact), is used to inflate the glass into a bubble. The cane pattern expands and flattens as the bubble grows.
- Attaching a Stem: A clear glass stem is prepared and attached to the blown object.
- Finishing and Annealing: The object is separated from the blowpipe by shocking a specific point with a drop of water. The sharp edge is then melted smooth.
Annealing Process
To prevent internal stresses and ensure the glass object's durability, it must be annealed. This involves slowly cooling the glass in an oven.
Annealing Profile (Temperature vs. Time): * Hold at Annealing Temperature: The glass is placed in an oven at its annealing temperature (e.g., 930°F for the demonstrated glass). It is held at this temperature for a duration dependent on the glass's thickness (e.g., 30 minutes for thin pieces, up to a year for very thick objects like telescope lenses) to allow the temperature to equalize throughout the piece. * Gradual Cooling to Strain Point: The temperature is then gradually lowered to the strain point (e.g., 750°F), which is about 100-150°F below the annealing temperature. This phase is critical and requires slow cooling (e.g., 1-2 hours) to gently pass through the region where internal stresses are most likely to form. * Faster Cooling to Room Temperature: After passing the strain point, the glass can be cooled more quickly (e.g., 4 hours) down to around 300°F, and then to room temperature.
The entire annealing process typically takes about eight hours overnight, ensuring that no stresses remain in the finished glass.
Takeaways
- Glass compositions give different coefficients of thermal expansion, causing stress when combined and cooled together.
- Tempering rapidly cools the exterior of hot glass, creating compressive outer layers and tensile inner layers, which increases strength and makes breakage safer.
- Hypertempering, demonstrated with Prince Rupert drops, uses water quenching to generate extreme internal stress, producing a head that is incredibly strong but a tail that, when broken, causes instantaneous disintegration.
- The MIT Glass Lab’s continuous feed furnace can operate for years without shutdown, providing a steady supply of molten glass, while reheating “glory holes” are used for localized heating during work.
- The lab’s blowing process builds a cane object by arranging colored canes on a preheated plate, fusing them on a marver, inflating with foot‑pedal air, and then annealing the piece through a controlled cooling schedule to relieve stress.
Frequently Asked Questions
What is hypertempering and how does it differ from regular tempering?
Hypertempering is an extreme form of tempering where molten glass is dropped into room‑temperature water instead of being cooled with air, creating far greater surface‑to‑core temperature gradients and thus much higher internal stresses. This results in Prince Rupert drops that have a very strong bulbous head but a tail that, when damaged, triggers rapid catastrophic failure.
Why does breaking the tail of a Prince Rupert drop cause the whole drop to shatter instantly?
Breaking the tail of a Prince Rupert drop releases the stored tensile stress, causing a stress wave that travels through the glass at the speed of sound, instantly fracturing the entire structure. The rapid propagation of this wave explains why the whole drop disintegrates in a fraction of a second.
Who is MIT OpenCourseWare on YouTube?
MIT OpenCourseWare is a YouTube channel that publishes videos on a range of topics. Browse more summaries from this channel below.
Does this page include the full transcript of the video?
Yes, the full transcript for this video is available on this page. Click 'Show transcript' in the sidebar to read it.
Helpful resources related to this video
If you want to practice or explore the concepts discussed in the video, these commonly used tools may help.
Links may be affiliate links. We only include resources that are genuinely relevant to the topic.